Profibus Gateway
Profibus Gateway ถูกสร้างให้เป็นบัสสำหรับเชื่อมต่ออุปกรณ์สำหรับระบบ Automation และกระบวนการผลิตในโรงงานอุตสาหกรรมต่างๆ Profibus ได้รับตราฐาน IEC 61158 และ IEC 61784 เพื่อให้ผู้ใช้สามารถใช้ระบบสื่อสารที่ทรงพลังของ Profibus ได้ง่ายขึ้นเราขอนำเสนอผลิตภัณฑ์ Profibus Gateway หลากหลายรุ่นให้ท่านเลือกใช้งาน
Series Specifications
View All Products
GW-7552 series
GW-7552 series คือ Gateway device ที่ทำหน้าที่เป็นตัวกลางในการเชื่อมต่อระหว่าง Modbus RTU , Profibus
Hardware Specifications
Hardware | |
CPU | 80186, 80 MHz or compatible |
SRAM/Flash/EEPROM | 512 KB / 512 KB / 16 KB |
Watchdog | Watchdog IC CPU built-in |
ESD Protection | 4 kV class A |
PROFIBUS Interface | |
Controller | Siemens SPC3 |
Transceiver | ADI ADM2486 |
Connector | 9-pin female D-Sub |
Baud Rate (bps) | 9.6 k, 19.2 k, 45.45 k, 93.75 k, 187.5 k, 500 k, 1.5 M, 3 M, 6 M, 12 M |
Transmission Distance (m) | Depend on baud rate (for example, max. 1200 m at 9.6 kbps ) |
Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for bus-to-logic |
Protocol | DP-V0 |
UART Interface | |
COM | RS-232/RS-422/RS-485(can’t be used simultaneously) |
COM Connector | 3-pin screwed terminal block (RxD, TxD, GND) 4-pin screwed terminal block (RxD+, RxD-, TxD+, TxD-) 2-pin screwed terminal block (DATA+, DATA-) |
Baud Rate (bps) | 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
Data bit | 7, 8 |
Stop bit | 1, 2 |
Parity | None, Even, Odd |
LED | |
Round LED | PWR LED, RUN LED, ERR LED |
Power | |
Power supply | Unregulated +10 ~ +30 VDC |
Protection | Power reverse polarity protection, Over-voltage brown-out protection |
Power Consumption | 2.5 W |
Mechanism | |
Installation | DIN-Rail |
Dimensions | 72 mm x 33 mm x 119 mm (W x L x H) |
Environment | |
Operating Temp. | -25 ~ 75℃ |
Storage Temp. | -30 ~ 85℃ |
Humidity | 5 ~ 95% RH, non-condensing |
Features
Protocol & Hierarchy | DP-V0 Slave |
Supports PROFIBUS Transmission Rate (Kbps) | 9.6, 19.2, 45.45, 93.75, 187.5, 500, 1500, 3000, 6000, 12000 |
Transmission Rate Setting | detected automatically |
Max Input Data Length | 132 Bytes |
Max Output Data Length | 131 Bytes |
Address Setting | 0~126 set by DIP switch |
Supports Modbus Mode | Master/Slave |
Supports Modbus Format | RTU/ASCII |
Hybrid COM 1 | RS-232/422/485 with “Self Tuner” inside |
Supports COM 1 Baudrate (Kbps) | 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, 115.2 |
Supports COM 1 Data Format | 7/8 data bits, No/Odd/Even parity, 1/2 stop bit |
Indicators | PWR, ERR, and RUN LEDs |
Network Isolation Protection | High Speed iCoupler |
DC Isolation Protection | 3000VDC on PROFIBUS side |
Utility
The GW-7552 Utility helps users to configure the devices, and has following features:
- Provide GW-7552 safe value setting
- Display module parameters of the GW-7552
- Show module address configuration of the GW-7552
GW-7553 series
GW-7553 series คือ Gateway device ที่ทำหน้าที่เป็นตัวกลางในการเชื่อมต่อระหว่าง Modbus RTU , Modbus TCP , Profibus
Hardware Specifications
Hardware | |
CPU | 80186, 80 MHz or compatible |
SRAM/Flash/EEPROM | 512 KB / 512 KB / 16 KB |
Watchdog | Watchdog IC CPU built-in |
ESD Protection | 4 kV class A |
PROFIBUS Interface | |
Controller | Profichip VPC3+C |
Transceiver | ADI ADM2486 |
Connector | 9-pin female D-Sub |
Baud Rate (bps) | 9.6 k, 19.2 k, 45.45 k, 93.75 k, 187.5 k, 500 k, 1.5 M, 3 M, 6 M, 12 M |
Transmission Distance (m) | Depend on baud rate (for example, max. 1200 m at 9.6 kbps ) |
Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for bus-to-logic |
Protocol | DP-V0 & DP-V1 |
UART Interface | |
COM | RS-232 (For updating firmware and configuration) |
COM Connector | 5-pin screwed terminal block (TxD, RxD, RTS, CTS, GND ) |
Baud Rate (bps) | 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
Data bit | 7, 8 |
Stop bit | 1, 2 |
Parity | None, Even, Odd |
Ethernet Interface | |
Controller | 10/100Base-TX Ethernet Controller (Auto-negotiating, Auto_MDIX) |
Connector | RJ-45 with LED indicator |
LED | |
Round LED | PWR LED, RUN LED, ERR LED |
Power | |
Power supply | Unregulated +10 ~ +30 VDC |
Protection | Power reverse polarity protection, Over-voltage brown-out protection |
Power Consumption | 2.5 W |
Mechanism | |
Installation | DIN-Rail |
Dimensions | 72mm x 33mm x 119mm (W x L x H) |
Environment | |
Operating Temp. | -25 ~ 75 ℃ |
Storage Temp. | -30 ~ 85℃ |
Humidity | 5 ~ 95% RH, non-condensing |
Features
Protocol & Hierarchy | DP-V0 & DP-V1 Slave |
Supports PROFIBUS Transmission Rate (kbps) | 9.6, 19.2, 45.45, 93.75, 187.5, 500, 1500, 3000, 6000, 12000 |
Transmission Rate Setting | detected automatically |
Max Input Data Length | 240 Bytes |
Max Output Data Length | 240 Bytes |
Address Setting | 0~126 set by DIP switch or EEPROM |
Supports Modbus Mode | Master/Slave |
Supports Modbus Format | RTU/ASCII/TCP |
Ethernet | 10/100 Base-TX |
Supports COM 1 Baudrate (kbps) | 2.4, 4.8, 9.6, 19.2, 38.4, 57.6, 115.2 |
Supports COM 1 Data Format | 7/8 data bits, No/Odd/Even parity, 1/2 stop bit |
Indicators | PWR, ERR, and RUN LEDs |
Network Isolation Protection | 2500 Vrms High Speed iCoupler |
DC Isolation Protection | 3000 VDC on PROFIBUS side |
GW-7553 series
GW-7553 series คือ Gateway device ที่ทำหน้าที่เป็นตัวกลางในการเชื่อมต่อระหว่าง CANopen , Profibus
Hardware Specifications
| Hardware | |
| CPU | 80186, 80 MHz or compatible |
| SRAM/Flash/EEPROM | 512 KB / 512 KB / 16 KB |
| Watchdog | Watchdog IC CPU built-in |
| ESD Protection | 4 kV class A |
| PROFIBUS Interface | |
| Controller | Profichip VPC3+C |
| Transceiver | ADI ADM2486 |
| Connector | 9-pin female D-Sub |
| Baud Rate (bps) | 9.6 k, 19.2 k, 45.45 k, 93.75 k, 187.5 k, 500 k, 1.5 M, 3 M, 6 M, 12 M |
| Transmission Distance (m) | Depend on baud rate (for example, max. 1200 m at 9.6 kbps ) |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for bus-to-logic |
| Protocol | DP-V0 |
| CAN Interface | |
| Controller | NXP SJA1000T with 16 MHz clock |
| Connector | 3-pin screwed terminal block (CAN_L, CAN_H, CAN_GND) |
| Isolation | 1000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Protocol | CANopen DS-301 ver4.02 |
| UART Interface | |
| COM | RS-232 (For updating firmware and configuration) |
| COM Connector | 3-pin screwed terminal block (RxD, TxD, GND) |
| Baud Rate (bps) | 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
| Data bit | 7, 8 |
| Stop bit | 1, 2 |
| Parity | None, Even, Odd |
| LED | |
| Round LED | PWR LED, RUN LED, ERR LED |
| Power | |
| Power supply | Unregulated +10 ~ +30 VDC |
| Protection | Power reverse polarity protection, Over-voltage brown-out protection |
| Power Consumption | 2.5 W |
| Mechanism | |
| Installation | DIN-Rail |
| Dimensions | 72 mm x 33 mm x 119 mm (W x L x H) |
| Environment | |
| Operating Temp. | -25 ~ 75℃ |
| Storage Temp. | -30 ~ 85℃ |
| Humidity | 5 ~ 95% RH, non-condensing |
Features
| Protocol & Hierarchy | DP-V0 Slave |
| Supports PROFIBUS Transmission Rate (Kbps) | 9.6, 19.2, 45.45, 93.75, 187.5, 500, 1500, 3000, 6000, 12000 |
| Transmission Rate Setting | detected automatically |
| Max Input Data Length | 240 Bytes |
| Max Output Data Length | 240 Bytes |
| PROFIBUS Address Setting | 0~126 set by DIP switch |
| Supports CANopen Standard | CiA CANopen Standard DS-301 v4.02 |
| Supports CANopen Consumer protocol | Node Guarding and Heartbeat Consumer protocol |
| Number of CANopen Commands | Support 110 CANopen SDO/PDO commands |
| COM | RS-232 |
| Indicators | PWR, ERR, and RUN LEDs |
| Network Isolation Protection | 2500 Vrms High Speed iCoupler |
| DC Isolation Protection | 3000VDC on PROFIBUS side |
| Protocol & Hierarchy | DP-V0 Slave |
Utility
The GW-7553-CPM Utility helps users to configure the devices, and has following features:
- Add/remove CANopen slaves via RS-232
- Show diagnostic messages
- Provide test function for CANopen slave devices
GW-7557 series
GW-7557 series คือ Gateway device ที่ทำหน้าที่เป็นตัวกลางในการเชื่อมต่อระหว่าง HART , Profibus
Hardware Specifications
Hardware | |
CPU | 80186, 80 MHz or compatible |
SRAM/Flash/EEPROM | 512 KB / 512 KB / 16 KB |
Watchdog | Watchdog IC CPU built-in |
ESD Protection | 4 kV class A |
PROFIBUS Interface | |
Controller | Profichip VPC3+C |
Transceiver | ADI ADM2486 |
Connector | 9-pin female D-Sub |
Baud Rate (bps) | 9.6 k, 19.2 k, 45.45 k, 93.75 k, 187.5 k, 500 k, 1.5 M, 3 M, 6 M, 12 M |
Transmission Distance (m) | Depend on baud rate (for example, max. 1200 m at 9.6 kbps ) |
Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for bus-to-logic |
Protocol | DP-V0 |
HART Interface | |
HART Interface | 8-pin screwed terminal block |
HART Channel | 4 channels |
UART Interface | |
COM | RS-232 |
COM Connector | 3-pin screwed terminal block (RxD, TxD, GND) |
Baud Rate (bps) | Up to 115200 |
Data bit | 7, 8 |
Stop bit | 1, 2 |
Parity | None, Even, Odd |
LED | |
Round LED | PWR LED, RUN LED, ERR LED |
POWER | |
Power supply | Unregulated +10 ~ +30 VDC |
Protection | Power reverse polarity protection, Over-voltage brown-out protection |
Power Consumption | 2.0 W |
Mechanism | |
Installation | DIN-Rail |
Dimensions | 72 mm x 33 mm x 119 mm (W x L x H) |
Environment | |
Operating Temp. | -25 ~ 75℃ |
Storage Temp. | -30 ~ 85℃ |
Humidity | 5 ~ 95% RH, non-condensing |
Features
Protocol & Hierarchy | DP-V0 Slave |
Supports PROFIBUS Transmission Rate (kbps) | 9.6, 19.2, 45.45, 93.75, 187.5, 500, 1500, 3000, 6000, 12000 |
Transmission Rate Setting | detected automatically |
Max Input Data Length | 240 Bytes |
Max Output Data Length | 240 Bytes |
Address Setting | 0~126 set by DIP switch or EEPROM |
Supports HART Mode | point-to-point / multi-drop |
Support HART Master | Allow two HART Masters |
Support HART Channel | 4 channels |
Support HART Frame | Short/Long frame |
Support HART modules | Connecting up to 15 HART modules |
Support HART Burst mode | YES |
Indicators | PWR, ERR, and RUN LEDs |
Network Isolation Protection | 2500 Vrms High Speed iCoupler |
DC Isolation Protection | 3000 VDC on PROFIBUS side |